EASA Part 26 – CS 26 Definitions & Terms Used Ref – Regulation (EU) 2020/1159. Review by Sofema Aviation Services (SAS) www.sassofia.com
Introduction
Regulation (EU) nº 2015/640 establishes additional airworthiness specifications for operations and contains two annexes.
- Annex I (Part 26), Subpart A, is devoted to general provisions on the appropriate authority, temporarily inoperative equipment and demonstration of conformity.
- Subpart B focuses on large aircraft and contains specifications related to:
o Seats, berths, seat belts and harnesses;
o Location, access and markings of emergency exits;
o Emergency interior lighting and operation of emergency lights;
o Flammability of the coatings of cargo compartments;
o Fire protection for toilets;
o Acoustic warning of the landing gear and systems for opening and closing the flight crew compartment door – incapacitation of a crew member and
o Continuing structural integrity programme for ageing aeroplanes structures.
- Annex II contains an amendment to Annex III (part ORO) of Regulation (EU) No. 965/2012.
Definitions
MOPSC – “Maximum Operational Passenger Seating Configuration“ shall mean the maximum passenger seating capacity of an individual aircraft, excluding crew seats, established for operational purposes and specified in the operations manual.
“Large Aeroplane” means an aeroplane that has the Certification Specifications for large aeroplanes “CS-25” or equivalent in its certification basis;
“Large Helicopter” means a helicopter that has the Certification Specifications for large rotorcraft “CS-29” or equivalent in its certification basis;
“Low-occupancy Aeroplane” means an aeroplane that has a maximum operational passenger seating configuration of:
- Up to and including 19 seats, or;
- Up to and including one-third of the maximum passenger seating capacity of the type-certified aeroplane, as indicated in the aeroplane type-certificate data sheet (TCDS), provided that both of the following conditions are met:
o The total number of passenger seats approved for occupancy during taxiing, take-off or landing does not exceed 100 per deck;
o The maximum operational passenger seating configuration during taxiing, take-off or landing in any individual zone between pairs of emergency exits (or any dead-end zone) does not exceed one-third of the sum of the passenger seat allowances for the emergency exit pairs bounding that zone (using the passenger seat allowance for each emergency exit pairs as defined by the applicable certification basis of the aeroplane).
Note: For the purpose of determining compliance with this zonal limitation, in the case of an aeroplane that has deactivated emergency exits, it shall be assumed that all emergency exits are functional.
“Limit of Validity” (LOV) means, in the context of the engineering data that supports the structural maintenance programme, a period of time, stated as a number of total accumulated flight cycles or flight hours or both, during which it is demonstrated that widespread fatigue damage will not occur in the aeroplane;
“Airworthiness Limitation Section” (ALS) means
- A section in the instructions for continued airworthiness, as required by points 21.A.61, 21.A.107 and 21.A.120A of Annex I (Part 21) to Regulation (EU) No 748/2012.
- Contains airworthiness limitations that set out each mandatory replacement time, inspection interval and related inspection procedure;
“Corrosion Prevention and Control Programme” (CPCP) means a document reflecting a systematic approach to prevent and to control corrosion in an aeroplane’s primary structure, consisting of basic corrosion tasks, including inspections, areas subject to those tasks, defined corrosion levels and compliance times (implementation thresholds and repeat intervals).
- A baseline CPCP is established by the type certificate holder, which can be adapted by operators to create a CPCP in their maintenance programme specific to their operations;
“Widespread Fatigue Damage” (WFD) means a simultaneous presence of cracks at multiple locations in the structure of an aeroplane that are of such size and number that the structure will no longer meet the fail-safe strength or residual strength used for certification of that structure;
“Baseline Structure” refers to the structure that is designed under the type certificate for that aeroplane model (that is, the ‘as delivered aeroplane model configuration’);
“Fatigue-critical Baseline Structure” (FCBS) means the baseline structure of an aeroplane that is classified by the type certificate holder as a fatigue-critical structure;
“Fatigue-critical Modified Structure” (FCMS) means any fatigue critical structure of an aeroplane introduced or affected by a change to its type design and that is not already listed as part of the fatigue-critical baseline structure;
“Damage Tolerance Evaluation” (DTE) is a process that leads to a determination of maintenance actions necessary to detect or preclude fatigue cracking that could contribute to a catastrophic failure. When applied to repairs and changes, a DTE includes the evaluation of the repair or change and the fatigue critical structure affected by the repair or change;
“Damage Tolerance Inspection” (DTI) means a documented inspection requirement or other maintenance action developed by holders of a type-certificate or restricted type-certificate as a result of a damage tolerance evaluation.
- A DTI includes the areas to be inspected, the inspection method, the inspection procedures (including the sequential inspection steps and acceptance and rejection criteria), the inspection threshold and any repetitive intervals associated with those inspections.
- DTIs may also specify maintenance actions such as replacement, repair or modification;
“Repair Evaluation Guideline” (REG) means a process established by the type certificate holder that guides operators to establish damage tolerance inspections for repairs that affect fatigue-critical structure to ensure the continued structural integrity of all relevant repairs;
“Fatigue-critical Structure” (FCS) means a structure of an aeroplane that is susceptible to fatigue cracking that could lead to a catastrophic failure of the aeroplane.
Next Steps
Follow this link to our Library to find & Download related documents for Free.
Sofema Aviation Services www.sassofia.com & Sofema Online www.sofemaonline.com provide EASA regulatory compliant and vocational training including related to CAMO, AMC20-20 and Part 26 / CS 26. If you want more information, please see the websites or email us at team@sassofia.com
Tags:
Airworthiness Limitation Section, Annex I, Annex I (Part 26), Annex II, Annex III (Part-ORO), Baseline Structure, Certification specifications (CS), Corrosion Prevention and Control Programme (CPCP), CS 26, Damage Tolerance Evaluation (DTE), Damage Tolerance Inspections (DTI), EASA CS-25, EASA CS-29, EASA Part 26, Fatigue-critical Baseline Structures (FCBSs), Fatigue-critical Modified Structure (FCMS), Fatigue-critical Structure (FCS), Large Aeroplane, Large Helicopter, Limit of Validity (LOV), Low-occupancy Aeroplane, MOPSC, Part 26, Regulation (EU) 2020/1159, Regulation (EU) nº 2015/640, Repair Evaluation Guidelines (REGs), SAS blogs, Widespread Fatigue Damage (WFD)
